Want to receive product discounts and updates? Get it Here!

Pulsar Generator Repair

* This site contains affiliate links for which we may be compensated.

As important as generators can be in our daily lives, they can also malfunction. There is nothing more frustrating than a generator that has refused to work or does not run well. Therefore, it is quite important to know how to effectively troubleshoot your generator.

Pulsar Generator Troubleshooting


Why is my generator having a difficult time starting?
Sometimes, this happens when you have not used your generator in a long time. Check the oil level and top it up. This could also be as a result of overheating. Make sure to install the generation in a well-ventilated compartment.

Why is my generator not supplying power?
Check if the alternator has been de-energized and re-energize it. Replace the alternator if necessary. Also, check the circuit breakers. They could be the major cause of the problem, to begin with.

Low power supply
This could be as a result of incorrect motor operation. Remedies to this problem include cleaning out of the carburetor, the air filter, and the fuel filter.

If you’re looking for Pulsar generator repair and service manual check out the books or instructions below:

You can download the manual for any pulsar generator model by taking the following steps;
• Go to Pulsar Generator homepage
• Scroll down and click on generators
• You get a page that shows different Pulsar generator models
• Click on any of the models you want
• Scroll down to downloads to get the owner’s manual

You can also go here to find Pulsar generator parts diagram and manual for many generator models or find Pulsar generator physical manual on eBay.

Pulsar Generator DIY Repair


If the Pulsar generator is experiencing any of the above-stated problems, they can be easily handled at your end.

If the engine is having a hard time getting started, you probably need to fill the fuel tank with the necessary gas, or you may also need to fix the leads connected to the spark plug.

If your portable generator is a generator that runs on gas, make sure you have the proper oil levels at all times. Your generator requires a certain amount of oil to work just like an engine that runs on gas. You may need to check the oil levels frequently. And make sure there is enough oil as the generator requires. Also, ensure you are changing the oil out with fresh oil on a regular basis.

Replacing a fuel filter, simply detach the fuel line where it is fixed to the carburetor. Try holding it over a bucket or container to catch leftover fuel. Run your generator and pay attention to whether or not any or enough fuel is seeping through the filter. If you discover that the fuel is not passing through the filter, it might just be the right time to replace the filter.

Pulsar Generator Local Repair Shops Near Me and Certified Repair Service


If after trying all the repair tricks mentioned above and nothing works out, you can contact the company’s certified repair service center or a local repair shop. The contact of the local service center can be found on the internet. Simply go to the company’s official website www.pulsar-products.com. Click on the “Contact” link displayed at the top of the webpage. » Pulsar Generator support

Find Pulsar Generators Repair Shops Near Me

Popular Pulsar Generator Models


– The Pulsar PG3250 is one of the simplest open-frame generators we have seen.
– Pulsar PG7500B – Dual Fuel Generator. The Pulsar 7500 comes with FOUR 120V receptacles as well as a 30 amp twist RV Outlet and a 120/240amp twist outlet.
– Pulsar PG2000iS- this is an inverter generator. It is equipped with the most amounts of outlets (USB, 2 AC, 12V Cigarette Lighter, & Parallel Connection) of any other 2000-3000 watt generator.
– Pulsar 3,250W Portable Gas-Powered Generator, PG3250.

Regular maintenance can correct and prevent a variety of issues. Some of these issues could damage your generator permanently, forcing you to purchase a new one.

Looking for generator parts? Visit this page and find out where to buy cheap and genuine Pulsar generator parts.

2 comments | Add One

  1. McGoo - 06/16/2023 at 3:17 pm

    I have a Pulsar PG4500ISR Generator which worked very well for about the first 30 hours. It then started running weaker and weaker until it would not run at all. We live at 8000ft elevation and our camping activities are generally higher than our home.
    I would like to find a repair shop near Cheyenne, WY. if one exists.

  2. Richie - 01/9/2024 at 8:33 pm

    moved back from florida, gen wont start
    pulsar pc6000
    only used it for weather outings almost new condition

Leave a Comment

First Name:

E-Mail: (will NOT be publish)


Please note: Generatorstop.com is only a "guide/resource" website and we are NOT associated with any of the companies or products listed here.